Fiber Optic Splicing Equipment

In the process of optical communication, the use of fiber fusion splicer is indispensable. Fiber optic fusion splicers are used for the construction and maintenance of optical fibers, and fiber optic fusion splices are normal on wiring sites. However, many friends may not be particularly familiar with the use process of fiber optic fusion machines. Although fiber optic fusion operations are mainly completed by fiber optic fusion machines, a cutting knife should be used to cut the end face of the fiber optic before fusion. Do not pull on the fiber optic during fusion to prevent poor fusion. After fusion is completed, the final step is to heat the shrink tube.

Built-in IoT Module for Mobile Data Communication

Web-based, Real-time Operation System

Active V-Groove Clad Alignment Splicing Method

The Highest Magnification and Resolution

5" Color LCD Touch Screen

Double Tapping ( Zoom in & Out )

Detachable SOC Holder and Heating Oven

3 Bright LEDs for Dark Environment

Ceramic Clamp for Improved Durability

Q: How to repair the broken fiber optic splicing equipment?

After long-term use, fiber optic fusion splicers inevitably encounter some problems. Sometimes, the machine experiences fatal faults, such as damage to internal components, which require repair at the factory. However, most of the time, simple faults occur that can be resolved by the user themselves. For example, many fiber optic fusion splicers do not react to the machine after being turned on, which is just a small issue in daily maintenance.

1. After turning on the switch of the fiber optic fusion splicer, the screen showed no brightness, and after opening the windshield, it was found that the horizontal lighting on the electrode base was not on.

Solution:

(1) Check if the power plug socket is properly plugged in, and if not, plug it in again.

(2) Check if the power fuse is disconnected, and if it is, replace the backup fuse.

2. The fiber optic can be reset normally. When setting the gap, the screen darkens, there is no fiber optic image, and the screen display stops at "setting the gap".

Solution:

Check and confirm if the windshield is pressed in place or if the springs are in good contact.

3. After turning on the fiber optic fusion splicer, "Battery depleted" appears below the screen and the buzzer keeps ringing.

Solution:

(1) This phenomenon generally occurs when using battery power, and only needs to replace the power supply.

(2) Check and confirm if the power fuse box is tightened.

4. The fiber optic can be reset normally, and when setting the gap, the fiber appears on the screen but stops moving, and the screen display stops at "set gap".

Solution:

(1) Press the "Reset" button to reset the system.

(2) Open the windshield and open the left and right pressure plates respectively. Perform the following checks in sequence:

(3) Check for broken fibers.

(4) Check if the fiber cutting length is too short.

(5) Check if the fiber tray matches the fiber optic cable. And carry out corresponding processing.

5. The optical fiber can be reset normally. When setting the gap, the fiber continues to move backwards, and the screen displays "Set Gap" and "Reinstall Fiber".

Solution:

It may be caused by excessive dust deposition on the eyepiece of the microscope in the optical system. Use a cotton swab to wipe the eyepiece of the horizontal and vertical microscopes. If there is no obvious dust observed with the eyes, try again.

6. The optical fiber can be reset normally. When setting the gap, the screen will display "Set Gap", and after a period of time, the screen will display "Reinstall Optical Fiber".

Solution:

(1) Press the "Reset" button to reset the system.

(2) Open the windshield and open the left and right pressure plates respectively. Perform the following checks in sequence:

(3) Check for broken fibers.

(4) Check if the fiber cutting length is too short.

(5) Check if the fiber tray matches the fiber optic cable. And carry out corresponding processing.

If the common faults of the fiber optic fusion splicer cannot be solved according to the above methods, they can be returned to the manufacturer for repair.

Hot Tags: fiber optic splicing equipment, China fiber optic splicing equipment manufacturers, suppliers, Fiber Cleaver Kit, , Optical Light Source and Power Meter